MQSensorsLib/examples/ESP32/esp32.ino

// This is an example of implementation using ESP8266
// Never connect the sensor direct to the ESP8266, sensor high level is 5V
// ADC of ESP8266 high level is 3.3
// To connect use a voltage divisor, where 5V will 3v3 on the middle point like
// this {{URL}}

/*
  MQUnifiedsensor Library - reading an MQSensor using ESP8266 board

  For this example wi will demonstrates the use a MQ3 sensor.
  Library originally added 01 may 2019
  by Miguel A Califa, Yersson Carrillo, Ghiordy Contreras, Mario Rodriguez
 
  Added ESP8266 example 
  29.03.2020
  Wiring:
  https://github.com/miguel5612/MQSensorsLib_Docs/blob/master/static/img/MQ_ESP8266.PNG

 This example code is in the public domain.

*/

//Include the library
#include <MQUnifiedsensor.h>
/************************Hardware Related Macros************************************/
#define         Board                   ("ESP-32") // Wemos ESP-32 or other board, whatever have ESP32 core.
#define         Pin                     (25)  //IO25 for your ESP32 WeMos Board, pinout here: https://i.pinimg.com/originals/66/9a/61/669a618d9435c702f4b67e12c40a11b8.jpg
/***********************Software Related Macros************************************/
#define         Type                    ("MQ-3") //MQ3 or other MQ Sensor, if change this verify your a and b values.
#define         Voltage_Resolution      (3.3) // 3V3 <- IMPORTANT. Source: https://randomnerdtutorials.com/esp32-adc-analog-read-arduino-ide/
#define         ADC_Bit_Resolution      (12) // ESP-32 bit resolution. Source: https://randomnerdtutorials.com/esp32-adc-analog-read-arduino-ide/
#define         RatioMQ3CleanAir        (60) // Ratio of your sensor, for this example an MQ-3
/*****************************Globals***********************************************/
MQUnifiedsensor MQ3(Board, Voltage_Resolution, ADC_Bit_Resolution, Pin, Type);
/*****************************Globals***********************************************/

void setup() {
  //Init the serial port communication - to debug the library
  Serial.begin(9600); //Init serial port

  //Set math model to calculate the PPM concentration and the value of constants
  MQ3.setRegressionMethod(1); //_PPM =  a*ratio^b
  MQ3.setA(4.8387); MQ3.setB(-2.68); // Configure the equation to to calculate Benzene concentration
  /*
    Exponential regression:
  Gas    | a      | b
  LPG    | 44771  | -3.245
  CH4    | 2*10^31| 19.01
  CO     | 521853 | -3.821
  Alcohol| 0.3934 | -1.504
  Benzene| 4.8387 | -2.68
  Hexane | 7585.3 | -2.849
  */

  /*****************************  MQ Init ********************************************/ 
  //Remarks: Configure the pin of arduino as input.
  /************************************************************************************/ 
  MQ3.init(); 
 
  /* 
    //If the RL value is different from 10K please assign your RL value with the following method:
    MQ3.setRL(10);
  */
  /*****************************  MQ CAlibration ********************************************/ 
  // Explanation: 
   // In this routine the sensor will measure the resistance of the sensor supposedly before being pre-heated
  // and on clean air (Calibration conditions), setting up R0 value.
  // We recomend executing this routine only on setup in laboratory conditions.
  // This routine does not need to be executed on each restart, you can load your R0 value from eeprom.
  // Acknowledgements: https://jayconsystems.com/blog/understanding-a-gas-sensor
  Serial.print("Calibrating please wait.");
  float calcR0 = 0;
  for(int i = 1; i<=10; i ++)
  {
    MQ3.update(); // Update data, the arduino will read the voltage from the analog pin
    calcR0 += MQ3.calibrate(RatioMQ3CleanAir);
    Serial.print(".");
  }
  MQ3.setR0(calcR0/10);
  Serial.println("  done!.");
  
  if(isinf(calcR0)) {Serial.println("Warning: Conection issue, R0 is infinite (Open circuit detected) please check your wiring and supply"); while(1);}
  if(calcR0 == 0){Serial.println("Warning: Conection issue found, R0 is zero (Analog pin shorts to ground) please check your wiring and supply"); while(1);}
  /*****************************  MQ CAlibration ********************************************/ 
  MQ3.serialDebug(true);
}

void loop() {
  MQ3.update(); // Update data, the arduino will read the voltage from the analog pin
  MQ3.readSensor(); // Sensor will read PPM concentration using the model, a and b values set previously or from the setup
  MQ3.serialDebug(); // Will print the table on the serial port
  delay(500); //Sampling frequency
}