Version 2.0.1

Fixed the error of not sending a configuration message after rebooting the gateway.
Fixed an error of the first hardware configuration saving.

hardware/README.md

@@ -29,7 +29,7 @@
     Internal button GPIO number     3
     Internal button trigger level   LOW
     External button GPIO number     14
-    External button trigger level   HIGH
+    External button trigger level   LOW
 
     Using MQTT:
 

main/zh_espnow_switch.c

@@ -44,7 +44,6 @@ void zh_load_config(switch_config_t *switch_config)
     uint8_t config_is_present = 0;
     if (nvs_get_u8(nvs_handle, "present", &config_is_present) == ESP_ERR_NVS_NOT_FOUND)
     {
-        nvs_set_u8(nvs_handle, "present", 0xFE);
         nvs_close(nvs_handle);
     SETUP_INITIAL_SETTINGS:
 #ifdef CONFIG_RELAY_USING
@@ -110,6 +109,7 @@ void zh_save_config(const switch_config_t *switch_config)
 {
     nvs_handle_t nvs_handle = 0;
     nvs_open("config", NVS_READWRITE, &nvs_handle);
+    nvs_set_u8(nvs_handle, "present", 0xFE);
     nvs_set_u8(nvs_handle, "relay_pin", switch_config->hardware_config.relay_pin);
     nvs_set_u8(nvs_handle, "relay_lvl", switch_config->hardware_config.relay_on_level);
     nvs_set_u8(nvs_handle, "led_pin", switch_config->hardware_config.led_pin);
@@ -129,7 +129,6 @@ void zh_load_status(switch_config_t *switch_config)
     uint8_t status_is_present = 0;
     if (nvs_get_u8(nvs_handle, "present", &status_is_present) == ESP_ERR_NVS_NOT_FOUND)
     {
-        nvs_set_u8(nvs_handle, "present", 0xFE);
         nvs_close(nvs_handle);
         zh_save_status(switch_config);
         return;
@@ -142,6 +141,7 @@ void zh_save_status(const switch_config_t *switch_config)
 {
     nvs_handle_t nvs_handle = 0;
     nvs_open("status", NVS_READWRITE, &nvs_handle);
+    nvs_set_u8(nvs_handle, "present", 0xFE);
     nvs_set_u8(nvs_handle, "relay_state", switch_config->status.status);
     nvs_close(nvs_handle);
 }
@@ -479,7 +479,7 @@ void zh_espnow_event_handler(void *arg, esp_event_base_t event_base, int32_t eve
         break;
     case ZH_ESPNOW_ON_SEND_EVENT:;
         zh_espnow_event_on_send_t *send_data = event_data;
-        if (send_data->status == ZH_ESPNOW_SEND_FAIL && switch_config->gateway_is_available == true)
+        if (send_data->status == ZH_ESPNOW_SEND_FAIL)
         {
             switch_config->gateway_is_available = false;
             vTaskSuspend(switch_config->switch_attributes_message_task);

main/zh_espnow_switch.h

@@ -13,25 +13,18 @@
 
 #ifdef CONFIG_IDF_TARGET_ESP8266
 #define ZH_CHIP_TYPE HACHT_ESP8266
-// #define ZH_CPU_FREQUENCY CONFIG_ESP8266_DEFAULT_CPU_FREQ_MHZ;
 #elif CONFIG_IDF_TARGET_ESP32
 #define ZH_CHIP_TYPE HACHT_ESP32
-// #define ZH_CPU_FREQUENCY CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ;
 #elif CONFIG_IDF_TARGET_ESP32S2
 #define ZH_CHIP_TYPE HACHT_ESP32S2
-// #define ZH_CPU_FREQUENCY CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ;
 #elif CONFIG_IDF_TARGET_ESP32S3
 #define ZH_CHIP_TYPE HACHT_ESP32S3
-// #define ZH_CPU_FREQUENCY CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ;
 #elif CONFIG_IDF_TARGET_ESP32C2
 #define ZH_CHIP_TYPE HACHT_ESP32C2
-// #define ZH_CPU_FREQUENCY CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ;
 #elif CONFIG_IDF_TARGET_ESP32C3
 #define ZH_CHIP_TYPE HACHT_ESP32C3
-// #define ZH_CPU_FREQUENCY CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ;
 #elif CONFIG_IDF_TARGET_ESP32C6
 #define ZH_CHIP_TYPE HACHT_ESP32C6
-// #define ZH_CPU_FREQUENCY CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ;
 #endif
 
 #ifdef CONFIG_IDF_TARGET_ESP8266

version.txt

@@ -1 +1 @@
-2.0.0
+2.0.1