This library implements support for the MHZ16 CO2 sensor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
Implements the flex analog sensor. See
http://bildr.org/2012/11/flex-sensor-arduino/
for wiring instructions.
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
Instead of trying to call out the build environment for a .so to link
against, use the one UPM will build as a dependency.
Also add guards around the SWIG commands for both Node and Python
targets
Signed-off-by: Thomas Ingleby <thomas.c.ingleby@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The library implements support for the Adafruit MotorShield 1438:
http://www.adafruit.com/products/1438
This shield supports 4 DC motors or 2 Stepper motors.
It makes use of the pca9685 UPM library, and therefore requires that
PR #123 and PR #134 are merged first:
PR 123: pkgconfig.in: allow a module to specify dependencies on
another module
PR 134: pca9685: Initial implementation
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Grove EL Driver.
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The library implements support for the Adafruit MotorShield 1438:
http://www.adafruit.com/products/1438
This shield supports 4 DC motors or 2 Stepper motors.
It makes use of the pca9685 UPM library, and therefore requires that
PR #123 and PR #134 are merged first:
PR 123: pkgconfig.in: allow a module to specify dependencies on
another module
PR 134: pca9685: Initial implementation
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This library implements generic support for the pca9685 16 channel 12
bit PWM LED controller. This controller is used on some Adafruit
motor shields.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Grove I2C Motor Driver.
The device *requires* a 100Khz I2C bus speed. It will not work on
anything faster.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implementes support for the Grove QTouch sensor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
This was tested on the RobotBase Dual H-Bridge motor control board.
There are two examples:
l298-example: This example demonstrates using the class to contol one
of the H-Brdges to control a DC motor.
l298-stepper-example: This example demonstrates using the class to
control a 4-wire dual-phase stepper motor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
