Add functionality to read and set the low-power mode settings
Add functions to read and set the averaging factor per key
Add functions to read and set the adjecent key suppression (AKS) groups
Add a function to read the ID register
Add a sanity check to the constructor
Signed-off-by: Wouter van Verre <wouter.van.verre@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
Run .clang-format on the header and source files
Add missing braces
Signed-off-by: Wouter van Verre <wouter.van.verre@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module was developed and tested on the Grove NFC Tag. It is an
8KB EEPROM accessable (with various protection capabilites) via I2C
and NFC capable devices.
The code was based on the Seeed Studio example code with some help
from the datasheet.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module was developed on the Grove Serial Camera. It connects to
the UART and runs at 115200 baud. It was developed based on the Seeed
Studio Arduino sketch, as there appears to be no protocol
documentation available.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
There were a few issues with this driver, corrected in this update.
1) i2c transactions were not working - I replaced the i2c
implementation with the MRAA i2c class implementation.
2) status check was inverted - fixed.
3) fixed up #defines in header file to avoid naming collisions (ADDR,
etc).
4) Added capability to supply bus and i2c address to ctor, setting
defaults of 0, and TH02_ADDR respectively.
NOTE: For proper operation on Edison using the arduino breakout
board, the voltage needs to be set to 3.3V rather than 5v. On G2, 5v
works fine.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver implements support for the Sparkfun Single Lead Heart Rate
Monitor, based on the AD8232 chip.
It simply outputs ADC data that needs to be sent somewhere for
plotting. The Sparkfun page has some suggestions.
Alternatively, if you have an oscilliscope that supports a 'Roll'
mode, you can get an EKG-like display by measuring the OUT pin.
https://www.sparkfun.com/products/12650
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the Grove 3-Axis Digital
Accelerometer(±400g), using the h3lis331dl chip.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the DTMF Shield based on the ht9170.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Grove BLE (Bluetooth Low
Energy) device. It is implemented as a UART device accepting an "AT"
command set.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The module supports the LV-MaxSonar EZ1, EZ2, EZ3 and EZ4 ultrasonic
range finders. It was developed and tested on the EZ3 variant.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Adafruit UV sensor:
https://www.adafruit.com/products/1777
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>