Internal sensor onboard the Curie/Arduino101 can be accessed via Firmata using
this plugin. You will need mraa compiled with -DFIRMATA=ON for this to work and
be using Firmata with the CurieIMU firmata extension for ExtensibleFirmata
Signed-off-by: Ron Evans <ron@hybridgroup.com>
Signed-off-by: Justin Zemlyansky <jlstigman@live.com>
Signed-off-by: Brendan Le Foll <brendan.le.foll@intel.com>
This driver provides support for the ILI9341 LCD driver via SPI (e.g.
Adafruit 2.8" TFT LCD).
It was implemented and tested on the Edison.
Signed-off-by: Shawn Hymel
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the Omega RH-USB Humidity Probe with
Temperature sensor. It connects via an integrated USB cable, and
appears as a serial port.
It does not currently work with Edison (as of this date) due to
missing ftdi_sio and usbserial kernel support.
It was implemented and tested on the Galileo 2.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Veris HWXPHTX Hardware Protocol
Humidity and Temperature Sensor family. It uses MODBUS over an RS485
interface.
This module was developed using libmodbus 3.1.2, and the Veris HWXPHTX.
This sensor supports humidity, and optionally, temperature, slider
switch, and override switch reporting. The HWXPHTX used to develop
this driver did not include the optional slider or override switches,
however support for them is provided.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed using the Veris HD2NVSTA1 humidity
transmitter. The 'T' variant supports a temperature transmitter as
well. Both signals are provided by the device as analog 0-5Vdc or
0-10Vdc outputs.
The A1 variant supports a temperature range of -40C-50C, while the A2
variant supports a range of 0C-50C. Humidity ranges for all devices
in this device family range from 0% to 100% (non-condensing).
Temperature measurement can be disabled by passing -1 as the
temperature analog pin to the constructor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Comet System T3311 Temperature
and Humidity transmitter. It uses MODBUS over an RS232 serial port.
You must have libmodbus v3.1.2 (or greater) installed to compile and
use this driver.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
Initial commit of ADS1x15 adc converter. Support for both ADS1015 12 bit
and ADS1115 16 bit adc.
--signoff
Signed-off-by: Marc Graham <marc@m2ag.net>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This is a USB device from Numato Labs that is accessed via a UART. It
provides 16 GPIO's, 7 of which can be configured as analog inputs.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
If MODULE_LIST is set, cmake will only create examples that can be built
with avaialble modules. There has been significant change to cmake file.
Comments show you how to add new examples.
Signed-off-by: Henry Bruce <henry.bruce@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module was developed using the OpenZWave library (v1.3):
http://www.openzwave.com/
It was developed using a collection of devices (switches and a
multi-sensor) connected via an Aeon Z-Stick Gen5 USB dongle.
It can be used to query (and, where appropriate, set) Values on Nodes
connected to the ZWave network.
Checks are made in src/ozw/CMakeLists.txt to ensure that the
libopenzwave library is installed (via pkg-config). If not present,
then neither the module, nor the example will be built.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed using an SX1276 based shield on the Galileo
G2. It requires 3.3v of operation. It does not work with Edison, due
to SPI issues.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
This module was developed and tested on a Grove Ultrasonic Ranger module.
http://www.seeedstudio.com/wiki/Grove_-_Ultrasonic_Ranger
Signed-off-by: Jun Kato <i@junkato.jp>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
Add support for MCP9808 precision temp sensor. Implements all features
except for TCrit and TUpper and TLower locking. Functionality includes
alert, interrupt, resolution and hysteresis control.
Signed-off-by: Marc Graham <marc@m2ag.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The driver implements support for the DFRobot pH sensors. It was
tested with both the standard and Pro versions, calibrated with
standard buffer solutions at pH 4.01 and pH 7.0.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver was developed based on the DFRobot Triple Axis
accelerometer BMA220 (Tiny):
http://www.dfrobot.com/index.php?route=product/product&product_id=1085
This device can only run at 3.3v DC. Do not connect to 5v.
Added a private function definition for the installISR function. Done because C++
wasn't able to find the function definition for the java bindings.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver was tested with the DFRobot URM37 Ultrasonic Ranger, V4.
Both UART and analog access modes are supported.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This is a basic serial module that allows access to various XBee
devices via a UART port. It was tested with the XBee S6B WiFi Module
and the XBee S1 802.14.4 module.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
The current grovemd driver supported 'mode2' stepping, where the
driver simply passed various stepper commands to the board for it to
carry out on it's own.
This doesn't work very well (or at all if you have old/buggy firmware)
so add a new 'mode1' stepper capability. This mode lets the driver
manually control the stepping operation without requiring special
firmware.
This is now the default and recommended mode to use for stepper motors
on this device. It is also more flexible in terms of the maximum
number of steps you can do (mode2 was limited to 254 steps max).
This was tested using a bipolar NEMA-17 stepper motor with an
external 12v power supply.
Note: 'Mode1' and 'Mode2' are the Seeed Studio terms for these different
stepping modes.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This is a rewrite of the existing SM130 driver which was incomplete
and non-functional.
It was implemented using a Sparkfun SM130 module:
https://www.sparkfun.com/products/10126
... using a Sparkfun RFID Evaluation Shield:
https://www.sparkfun.com/products/10406
It operates in UART mode only. A port to support I2C communications
(requires a encrypted firmware reflash from SonMicro) should be
fairly trivial, if you have one of those.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: sisinty sasmita patra <sisinty.s.patra@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was implemented using a Grove IMU 9DOF V2.0 (mpu9250).
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: sisinty sasmita patra <sisinty.s.patra@intel.com>
This driver provides support for the Grove GPRS shield, V2:
http://www.seeedstudio.com/wiki/GPRS_Shield_V2.0
It provides a simple interface whereby a user can send and receive
commands and data from the device. It is controlled by a standardized
set of "AT" commands. A full description of these commands is
available here:
http://www.seeedstudio.com/wiki/images/7/72/AT_Commands_v1.11.pdf
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed for the DFRobot Wheel Encoder, though it
could be used for any counting time-based task using a digital i/o pin
to generate interrupts.
http://www.dfrobot.com/index.php?route=product/product&product_id=98
If you want to use more than one encoder, simply create a class
instance for each one.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: sisinty sasmita patra <sisinty.s.patra@intel.com>
This driver was developed on a DFRobot CO2 sensor based on the MG811:
http://www.dfrobot.com/index.php?route=product/product&product_id=1023
It seems to *require* very precise calibration at 400ppm and 1000ppm
to be accurate. It also gets pretty hot (due to the heater) and
consumes significant current.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: sisinty sasmita patra <sisinty.s.patra@intel.com>
This driver supports the Sparkfun 64x48 pixel OLED Edison block:
https://www.sparkfun.com/products/13035
It is based on an ssd1306, but with some modifications (custom COM pin
mapping and a custom column offset). It uses SPI to communicate, and
since it is an Edison Block, you don't really have any options for
different bus and pin assignments.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the LSM9DS0 accelerometer,
magnetometer, and gyroscope.
It was developed on the Sparkfun 9DOF sensor block for Intel Edison.
https://www.sparkfun.com/products/13033
Commonly used capabilities are supported, and methods/register
definitions exist to easily implement any desired functionality that
is missing. Interrupt support has also been added.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver has been rewritten from scratch. It is implemented as 3
seperate drivers now (but all included as part of the mpu9150 UPM
library):
AK8975 (Magnetometer)
MPU60X0 (Accelerometer, Gyroscope, and Temperature sensor)
MPU9150 (composed of AK8975 and MPU60X0)
Each driver can be used independently and includes examples in
C++/JS/Python.
Commonly used capabilities are supported, and methods/register
definitions exist to easily implement any desired functionality that
is missing. Interrupt support has also been added.
Scaling support has also been properly implemented for both the
Accelerometer and Gyroscope.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed with a Sainsmart LCD Keypad Shield.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was written using an Adafruit PN532 board:
http://www.adafruit.com/products/364
It is based heavily on their arduino code, with significant
modifications.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the hp20x family of high accuracy
barometers. It was developed on the Grove Barometer (High Accuracy)
based on the HP206C.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
