This driver implements support for the Grove Recorder. It records up
to about 10 seconds of audio, and can play it back on command.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
This driver implements support for the Grove Water Flow sensor. It
uses an integrated hall effect sensor, connected to a GPIO configured
as an interrupt, to compute water flow in LPM (Liters Per Minute).
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
This driver was tested on a Grove Geared Stepper with Driver, the
uln2003a paired with a 28BYJ-48 unipolar stepper motor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
This driver implements support for the ZFM20 fingerprint module. It
was tested on a Grove Fingerprint Sensor.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: John Van Drasek <john.r.van.drasek@intel.com>
Additionally, add some error checking in the constructor, and determine
the ADC resolution and use that in the voltage calculation rather than
a hardcoded 1024.0.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The library implements support for the Adafruit MotorShield 1438:
http://www.adafruit.com/products/1438
This shield supports 4 DC motors or 2 Stepper motors.
It makes use of the pca9685 UPM library, and therefore requires that
PR #123 and PR #134 are merged first:
PR 123: pkgconfig.in: allow a module to specify dependencies on
another module
PR 134: pca9685: Initial implementation
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
The library implements support for the Adafruit MotorShield 1438:
http://www.adafruit.com/products/1438
This shield supports 4 DC motors or 2 Stepper motors.
It makes use of the pca9685 UPM library, and therefore requires that
PR #123 and PR #134 are merged first:
PR 123: pkgconfig.in: allow a module to specify dependencies on
another module
PR 134: pca9685: Initial implementation
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This library implements generic support for the pca9685 16 channel 12
bit PWM LED controller. This controller is used on some Adafruit
motor shields.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the Grove I2C Motor Driver.
The device *requires* a 100Khz I2C bus speed. It will not work on
anything faster.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Zion Orent <zorent@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
