The driver implements support for the DFRobot pH sensors. It was
tested with both the standard and Pro versions, calibrated with
standard buffer solutions at pH 4.01 and pH 7.0.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver was developed based on the DFRobot Triple Axis
accelerometer BMA220 (Tiny):
http://www.dfrobot.com/index.php?route=product/product&product_id=1085
This device can only run at 3.3v DC. Do not connect to 5v.
Added a private function definition for the installISR function. Done because C++
wasn't able to find the function definition for the java bindings.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This driver was tested with the DFRobot URM37 Ultrasonic Ranger, V4.
Both UART and analog access modes are supported.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
This is a basic serial module that allows access to various XBee
devices via a UART port. It was tested with the XBee S6B WiFi Module
and the XBee S1 802.14.4 module.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Abhishek Malik <abhishek.malik@intel.com>
The current grovemd driver supported 'mode2' stepping, where the
driver simply passed various stepper commands to the board for it to
carry out on it's own.
This doesn't work very well (or at all if you have old/buggy firmware)
so add a new 'mode1' stepper capability. This mode lets the driver
manually control the stepping operation without requiring special
firmware.
This is now the default and recommended mode to use for stepper motors
on this device. It is also more flexible in terms of the maximum
number of steps you can do (mode2 was limited to 254 steps max).
This was tested using a bipolar NEMA-17 stepper motor with an
external 12v power supply.
Note: 'Mode1' and 'Mode2' are the Seeed Studio terms for these different
stepping modes.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This is a rewrite of the existing SM130 driver which was incomplete
and non-functional.
It was implemented using a Sparkfun SM130 module:
https://www.sparkfun.com/products/10126
... using a Sparkfun RFID Evaluation Shield:
https://www.sparkfun.com/products/10406
It operates in UART mode only. A port to support I2C communications
(requires a encrypted firmware reflash from SonMicro) should be
fairly trivial, if you have one of those.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: sisinty sasmita patra <sisinty.s.patra@intel.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was implemented using a Grove IMU 9DOF V2.0 (mpu9250).
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: sisinty sasmita patra <sisinty.s.patra@intel.com>
This driver supports the Sparkfun 64x48 pixel OLED Edison block:
https://www.sparkfun.com/products/13035
It is based on an ssd1306, but with some modifications (custom COM pin
mapping and a custom column offset). It uses SPI to communicate, and
since it is an Edison Block, you don't really have any options for
different bus and pin assignments.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This module implements support for the LSM9DS0 accelerometer,
magnetometer, and gyroscope.
It was developed on the Sparkfun 9DOF sensor block for Intel Edison.
https://www.sparkfun.com/products/13033
Commonly used capabilities are supported, and methods/register
definitions exist to easily implement any desired functionality that
is missing. Interrupt support has also been added.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver has been rewritten from scratch. It is implemented as 3
seperate drivers now (but all included as part of the mpu9150 UPM
library):
AK8975 (Magnetometer)
MPU60X0 (Accelerometer, Gyroscope, and Temperature sensor)
MPU9150 (composed of AK8975 and MPU60X0)
Each driver can be used independently and includes examples in
C++/JS/Python.
Commonly used capabilities are supported, and methods/register
definitions exist to easily implement any desired functionality that
is missing. Interrupt support has also been added.
Scaling support has also been properly implemented for both the
Accelerometer and Gyroscope.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
This driver was developed with a Sainsmart LCD Keypad Shield.
Signed-off-by: Jon Trulson <jtrulson@ics.com>
Signed-off-by: Mihai Tudor Panu <mihai.tudor.panu@intel.com>
